America's steel market is running on its own rules, and US mills have been using them to raise prices every single week.

What Happened

Nucor raised its consumer Spot Price for hot-rolled coil by $15 to $1,295 per short ton in a letter to customers dated 9 November. The price for its California Steel Industries joint venture also rose $15, to $1,365. Lead times stayed at three to five weeks. It was the 17th consecutive weekly increase.

The Nucor price is a published offer for spot orders, not an index. But because Nucor is the largest US steelmaker, buyers and rivals treat it as a reference, and other mills often follow its moves within days.

The broader market is even higher. US hot-rolled coil was put at $1,340 to $1,400 per short ton as of 6 November, up from $1,300 to $1,340 a week earlier. A weekly assessment on 3 November averaged $1,350, up $45 on the week.

A year ago the same spot coil traded at $825 to $865 per short ton. On the mid-points that is a rise of about 62%.

The climb has been relentless. Nucor's spot price was $1,190 on 8 September, so it has added $105, or nearly 9%, in two months.

Why It Happened

Supply is tight at the spot level. In October the US saw a shortage of spot offers of flat steel, which pushed up prices for both hot-rolled and cold-rolled coil. When mills are booked out and few tons are available for prompt delivery, the weekly price becomes a price-setting tool rather than a negotiation.

Raw material costs are rising. A November survey of US scrap Market Participants pointed to a forecast month-on-month rise of 7.1% in ferrous scrap prices. Most US flat steel is made in electric-arc furnaces that melt scrap, so higher scrap feeds straight into coil costs.

Imports are not capping the rally. In September, analysts noted that the price gap between US and foreign offers was at a historically high level, attracting buyers, but they did not expect that to bring domestic prices down. Trade protection keeps much of that cheaper foreign coil, such as Chinese coil at $485 a tonne FOB, out of reach.

How It Plays Out

US flat-steel producers stand to benefit while Nucor's weekly increases keep sticking, selling into a market where tight Supply supports prices. Service centres that bought early also gain, as their inventories rise in value.

Steel users carry the cost: automakers, appliance makers, equipment builders and construction firms. Every $100 per ton increase flows into their costs, and many will try to pass it on to consumers.

The rally has risks. Prices this high encourage imports where trade rules allow, and some buyers will cut orders or delay projects. The scrap survey suggests costs will keep rising in the short term, which supports mills, but Demand will decide how long the run lasts.

It helps to understand the units. A short ton is 2,000 pounds, about 907 kilograms, so $1,295 per short ton equals roughly $1,427 per metric tonne. On that basis US coil costs nearly three times as much as Chinese export coil at $485 a tonne. That gap is the clearest measure of how far tariffs and trade rules have separated the US steel market from the rest of the world.

Hot-rolled coil is also a bellwether for the broader economy. It is the raw material for pipes, car frames, appliances and structural steel, so rising prices eventually show up in the cost of vehicles, buildings and equipment. When prices rise for many consecutive weeks, buyers often accelerate orders to avoid further increases, which can extend the run but also sets up a sharper correction if demand cools.

Producers elsewhere in the world watch the US price for a different reason. A sustained gap between American and global prices encourages Investment in US capacity, but it also invites political debate about the cost of trade protection for manufacturers and consumers. Whether the rally continues will depend on how long buyers accept higher quotes and on how quickly new supply arrives.

Producers also keep a close eye on order books. If automotive and construction orders slow, mills may need to hold prices or discount to keep furnaces running. For now, though, tight spot availability means customers are accepting weekly increases, and that sustains the cycle until lead times start to lengthen.

Watching these indicators together, rather than any single price, gives the clearest read on whether the cycle is topping or still building.

What to Watch Next

  • Whether Nucor posts an 18th straight increase or holds flat.
  • Weekly price assessments for hot-rolled coil.
  • December scrap settlements in the US Midwest.
  • Mill lead times.

If lead times shorten from three-to-five weeks, mills are running out of pricing power.